Home > Products > LED Automobile Light > LED Tailgate Light

Product Categories

CONTACT US
Add: Dth building, xinfeng Industry zone, GuanLan Twon, ShenZhen 518110
M.B: +8618926064598
TEL: +86-755-29441823
FAX: +86-755-29441823
Email: admin@kingshowlight.com

Super Brighter 5050 LED Tailgate Light With Red & Reverse White LED

This is a new item with bigger 5050 LED which is 3 in 1 chips, the brightness is 3 times bighter than before. 1. DC12V operate, Ultra Bright 3 in 1 chips 2. 152cm size with black casing. 3. 4pin plug with 100cm 4 color wires 4. totally 60pcs Red LEDs & 30 white LED, with running, reverse, left turn & right turn, brake fuction

Product Details
Welcome to wholesale the super brighter 5050 led tailgate light with red & reverse white led made in China in stock from our factory. Known as one of the leading manufacturers and suppliers in China, we also offer the customized service with low price. Now, check the quotation with us.

LED Tailgate Light Bar

 

Warning: The installation of this kit is recommended to be installed by a licensed professional. The improper installation of this kit will void all warranties.

Please read the following instructions thoroughly before installing this kit.

1. First using a tape measure, measure the lip under your trucks tailgate to ensure there is enough clearance to mount your tailgate light bar.

2. Following your trucks owner’s manual, carefully remove the tailgate from your truck.

3. Use the included 3M tape to temporarily mount the LED light bar to your trucks tailgate.

4. Using a 1/8th drill bit, pre drill the four mounting holes into your trucks tailgate, this will make the following step much easier.

5. Securely mount the tailgate light bar to your truck using a drill and the provided screws.

6. Run the power wire with flat 4 pin connector behind your bumper and to your trucks flat 4 pin connection. You may need to secure the slack in the wire so that it does not hang below the bumper.

 

Product Data

Item No.

Size

LED Qty

LED Type

LM/LED

Lead Wire

Casing

60 Red & White

49 inch (3125px)

48 Red

24 White

SMD3528

6-8LM

Per LED

1 meter with Play Plug

PVC

60 Red & White

60 inch (3800px)

60 Red

30 White

SMD3528

6-8LM

Per LED

1 meter with Play Plug

PVC

60 Red & White

3-in-1 SMD Chips

60 inch (3800px)

60 Red

30 White

SMD5050

   20-22LM

   Per LED

1 meter with Play Plug

PVC

 

If you purchased LED Tailgate Light Bar with Reverse Light Option proceed with your installation using the following steps:

1. Carefully remove one of your tail light assemblies.

2. Power your truck on and put it into reverse, so that your factory reverse lights are illuminated. It is imperative that you set the parking brake.

3. Return to the rear of your truck and remove the bulb from your reverse light.

4. Using a volt meter, find the positive 12 volt wire that powers your reverse light.

5. Once you have found your factory reverse light wire, use a wire stripper to cut and strip the wire.

6. Run the light bar’s white reverse wire to your factory reverse wire.

7. Use a butt connector to connect the tailgate bar’s white reverse wire to the trucks factory reverse wire. You can also solder or use a 3M™ Scotchlok™ type connector to secure this connection.

8. Now you can re-install your tail light assembly and tailgate, and test your tailgate light bar for full functionality.

9. please don’t connect it on the flasher of the vehicle

 

Flat 4 Pin Connector Diagram:

A - Red Wire: Ground

B - White Wire: Running Lamp                 

C - Green Wire: Left Turn Signal (scanning from middle to left)

 & Brake Light

D - Black Wire: Right Turn Signal (scanning from middle to right)

 & Brake Light

R: Orange Wire : Reverse Wire-


Related Products
Quick Navigation
  • About Us
  • Products
  • News
  • Exhibition
  • Contact Us
  • Feedback
  • Newsletter
    Enter in your email address to receive deals and coupons.
    +86-755-29441823
    +86-755-29441823 admin@kingshowlight.com